Ge Top Load Washer Diagnostic Mode

GE front load washer repair can be tricky; however, this page is here to help. The way these washers are designed it is almost impossible to diagnose them without placing them in the service mode. In the service mode you have total control over the washer so that you can test components such as the motor, pump, inverter, water valve and others. Also while in the service mode, you can view error codes that are sometimes vital to accurately diagnose problems with these washers. This page will explain how to use the service mode to assist with GE front load washer troubleshooting.

1. Close the door. 2. Clear current cycles by pressing the power button. Make sure the screen is blank before attempting to enter the service mode. 3. Disconnect power to washer for at least 30 seconds. 4. Reconnect the power and within 30 seconds of reconnecting power complete the next step. 5. Press signal -delay start -signal – delay start. Note: Entering the service mode is a little different on models GFWN1000, GFAN1000,GFWN1100, and GFAN1100. To enter the service mode on these models press signal, extra rinse, signal and extra rinse. Press the same button sequence to exit the service mode. If you successfully enter the washer into the service, mode t01 will be displayed and the door will lock.

Never disconnect the power to the washer while it is in the service mode. Doing so may result in a damaged control board.

When you enter the service mode, t01 is displayed. This test mode has no diagnostic purpose. The main board is designed to work on multiple models and this mode is for setting the model. For the most part, you shouldn’t have to worry about this test mode when diagnosing. To enter this test mode, press start/pause and to exit press power.

To enter the error code test mode on a GE front load washer, rotate the control knob until t02 is displayed in the control panel then press start/pause to enter the test mode. This is where all error codes are stored. Once you have entered the test mode, you will see the most recent error code that the control has flagged. If you press start/pause you will see the next recent error code. If you continue to press start/pause you can view up to the ten most recent error codes. Most of the time there will be only one or two. Once you have diagnosed the washer it is very important to clear the error codes. If you don’t clear the error codes, when you have another problem the old error codes will still be there from an issue that has been resolved. To clear the error codes press and hold start/pause. Press power to exit this test mode and the display should go back to t02.

For a full list of error codes see this page GE Front Load Washer Error Codes

To enter the LED and buttons test mode on a GE front load washer, rotate the control knob until t04 is displayed in the control panel then press start/pause to enter the test mode. This test mode will test to see if each button works and each LED will light. Each light should blink once in a loop. To test the buttons, press each button and if the control senses that the button has been pressed, you will hear a beep. If you do not hear the beep, the button is broken and you will have to replace the main control. Press power to exit this test mode and the display should go back to t04.

To enter the water pump test mode, rotate the control knob until t05 is displayed in the control panel then press start/pause to enter the test mode. Once you have entered the test mode, “P” will be displayed and the pump will run for 60 seconds. After 60 seconds it will return to t05. To exit this test mode early, press power to return to t05.

If the washer will not pump out the first thing you should do is remove the bottom panel to access the pump clean out and then clean out the pump.

To enter the water level control test mode on a GE front load washer, rotate the control knob until t06 is displayed in the control panel then press start/pause to enter the test mode. This test has five steps as described below. Once you start the test, the water pump will begin to run and “E” will be displayed in the control panel. The “E” being displayed means that the tub is empty. If the tub is empty, but “E” is not displayed then the water level control is bad. Press start/pause to advance to the next level of the test. At this point the water will begin to run. When the water level in the tub reaches the foam level, “F” will be displayed in the control panel and water will stop running. Foam water level is about ¾ of an inch in the wash basket. Press start/pause to advance to the next level of the test. Water will start to run again and when the tub reaches the main level, “nl” will be displayed in the control panel and the water will stop running. The main water level is about 2 ½ inches of water in the wash basket. Press start/pause to advance to the next level of the test. Water will run until overflow water level is reached. Once the overflow level is reached, “oF” will be briefly displayed in the control panel. Overflow is approximately 6 inches above the door opening. Soon after the overflow water level is reached, the water pump will energize and pump the water out. Once the tub is empty again, “E” will be displayed again. Pressing power anytime during the test mode will exit the test mode.

To enter the water heater test mode on a GE front load washer, rotate the control knob until t07 is displayed in the control panel then press start/pause to enter the test mode. Once this test is entered, the washer will start to fill with water until the main water level is reached. Once the washer is filled to the main water level, the heater will come on and start to heat the water for five minutes. During this time, the temperature of the water will be displayed in the control panel. You should see the temperature steady rise if the heater is working. Once the five minutes is up the water pumps out and will automatically exit this test mode. Pressing power anytime during the test mode will exit the test mode.

To enter the hot water valve test mode on a GE front load washer, rotate the control knob until t08 is displayed in the control panel then press start/pause to enter the test mode. This is the hot water valve test mode. Once this test mode is entered, “hOt” will be displayed in the control panel and the hot water will start to run. Hot water will continue to run until the main water level is reached or you press power to exit the test mode. If the main water level is reached before the test mode is terminated, the washer will pump the water out and return to t08.

Note that some GE front load washer models do not have this test mode. This can be a little confusing because you can rotate the knob until t08 is displayed; however, when you press start/pause you hear two beeps and the display continues to display t08.

To enter the cold-water test mode on a GE front load washer, rotate the control knob until t09 is displayed in the control panel then press start/pause to enter the test mode. This is the cold-water valve test mode. Once this test mode is entered, “Cld” will be displayed in the control panel and the cold water will start to run. Cold water will continue to run until the main water level is reached or you press power to exit the test mode. If the main water level is reached before the test mode is terminated, the washer will pump the water out and return to t09.

Note that some GE front load washer models do not have this test mode. This can be a little confusing because you can rotate the knob until t09 is displayed; however, when you press start/pause you hear two beeps and the display continues to display t09.

To enter the tumble test on a GE front load washer, rotate the control knob until t10 is displayed then press start/pause to enter the test mode. Once the test mode is entered, “tt” will be displayed in the control panel and the spin basket will start to tumble in one direction for 5 seconds then reverse and tumble for 5 seconds in opposite direction. This will repeat continually until you exit the test mode by pressing the power button.

To enter the spin test on a GE front load washer, rotate the control knob until t11 is displayed then press start/pause to enter the test mode. Once the test mode is entered, the tub will start to spin and the rpm will be displayed in the control panel. When you first enter the test mode, the spin basket will ramp up to 400 rpm. If you press start/pause a second time the spin basket will ramp up to 1000 rpm. Since some displays can only display three digits you may see 999 or 0 in the display when the spin basket reaches 1000 rpm.

Before I talk about the dispenser motor test, I will explain the dispenser system. Most GE front load washer models have a dispenser. The dispenser has 4 positions and the dispenser motor switches the dispenser to each position by rotating a water diverter in the correct position. On the top of the dispenser there are four numbers that represent each position. You should also see the dispenser and an arrow. When the motor rotates, the arrow moves as well as the diverter (you can’t see the diverter) to the position that it needs to be in according to which cycle the washer is in. Position 1 corresponds to the pre-wash dispenser function. Position 2 corresponds to the wash dispenser function. Position 3 corresponds to the bleach dispenser function. Position 4 corresponds to the fabric dispenser function.

To enter the dispenser motor test mode on a GE front load washer, rotate the control knob until t12 is displayed then press start/pause to enter the test mode. Once the test mode is entered, the display will display “Pdt” and the dispenser motor will rotate the dispenser until the arrow is pointing to 1 and the washer will start to fill in the pre-wash compartment. Press start/pause to advance to the next level of the test. Once done, the dispenser will turn to the number 2 position, “ddt” will be displayed in the control panel and water will start to fill in the wash compartment. Press start/pause to advance to the next level of the test mode. Once done, “bdt” will be displayed in the control panel, the dispenser will turn to the number 3 position and water will start to fill in the bleach compartment. Press start/pause to advance to the final stage of this test. Once done, “Fdt” will be displayed in the control panel, the dispenser will turn to the number 4 position and water will start to fill in the fabric softener compartment.

If at anytime during the test, the main water level is reached, the washer will pump out the water and exit the test mode. Also, if you press power at anytime it will exit the test mode. Some GE front loader washer models don’t have a dispenser motor but still have a dispenser test mode. Modes with no dispenser motors have three water valves, one hot and two cold. The water valves are energized in combinations to fill the correct dispenser compartment.

To enter the dispenser test mode on a GE front load washer, rotate the control knob until t12 is displayed then press start/pause to enter the test mode. Then “ddt” will be displayed and the hot water valve will run to fill the detergent compartment. Press start/pause to advance and “bdt” will be displayed and the #2 cold water valve will run water into the bleach compartment. Press start/pause to advance, “Fdt” will be displayed, the #1 cold water valve and the #2 cold water valve will run to fill the fabric softener compartment. Press start/pause to advance, “HCt” will be displayed, the #1 cold water valve and the hot water valve will run to fill the detergent compartment.

To enter the spin ramp teston a GE front load washer, rotate the control knob until t14 is displayed then press start/pause to enter the test mode. Once the test mode is entered, the spin basket will start to spin and the rpm will be displayed in the control panel. First, it will ramp to 100 rpm then to 350 rpm and finally to 1000 rpm.

How Do I Find the Error Code on My GE Washer?Sometimes, the washing machine will display the error code on the control panel. However, it doesn’t always do this. If you don’t see the code, follow these steps to access the machine’s diagnostic mode:

Let’s walk through the list of GE washer fault codes, what they each mean and how you can fix them. Most of these can be resolved quickly at home without needing to call a professional.

We’ll start with front load GE washers (such as the Profile model) before going to top load GE washing machine error codes.

While we’re discussing front and top load machines, you may have different error codes if you have a stackable washer and dryer. Refer to your user manual for help.

What It Means: The washing machine is not filling or is filling too slowly (exceeding eight minutes).

How to Fix It: Ensure the water supply is on. Then ensure that the water valves are connected to the inlet hoses and are open. Try turning the water off and on again. If this doesn’t work, check that the water line isn’t frozen. Lastly, inspect the hose for kinks or clogs. You should try to replace the hose every five years.

What It Means: The flood protection drain is activated. The washer has detected an overflow.

How to Fix It: Try resetting the machine or retrying the washing cycle before moving on to the next steps. If that doesn’t work, check the water valves or water level. Faults or a poor water level can cause this code. If the water valve is at fault, you’ll see water getting into the machine even when it’s off. But if that’s not the cause, you can perform the water level control test via the machine’s service mode.

What It Means: The detergent dispenser is malfunctioning.

How to Fix It: Unplug the appliance and check the mechanical link on the dispenser drawer. Repair or replace any damaged parts. Another problem may be that the dispenser can’t get into the correct position, or the opening and closing parts aren’t working. Repair or replace damaged parts.

You may also get a “Tank Low” error code. This appears on SmartDispense machines. It alerts you that the tank needs re-filled or when there are 8-10 loads of detergent remaining.

What It Means: Motor related. The motor or inverter isn’t working correctly, is overloaded, or drawing too much current.

How to Fix It: Remove some items from the drum and restart the washing cycle. A heavy load can put strain on the motor. Another solution is to rotate the drum manually. If there are crunching or grinding noises, there might be something stuck between the drum and the outer tub, which you will need to remove.

If the above solution doesn’t work, you may need to test the wiring. If it’s faulty, the wiring will need to be replaced, and possibly the drive motor and inverter control board, too. In this situation, we recommend contacting GE for support.

What It Means: The drive motor is overheating.

How to Fix It: Start by clearing the code, exiting service mode, and unplugging the washing machine for 30 seconds. If the code remains, inspect the wiring to the drive motor while the machine is turned off. You want to look for loose wiring or damaged wiring. Repair or replace any that you notice. However, if the wiring looks okay, you will need to replace the drive motor and possibly, the inverter control board, too.

Replace the drive motor before the inverter control board. Check how the machine works with just that replacement. If it still isn’t working, then replace the inverter control board, too. If you do need to replace either of these parts, we recommend contacting a GE repair person or a professional appliance repair provider instead of doing it yourself.

What It Means: The main control board is faulty. If this occurs, your machine will not work correctly.

How to Fix It: Unplug the appliance and check the wiring to the control board. Look for loose or damaged wires. Repair or replace them if you are able. Power the machine back up. If the problem continues, you will need to replace the entire control board.

This is a significant and expensive error, so take note of this hack. This error can also appear if a key is stuck on the control panel. So ensure that isn’t the case first before replacing the whole board.

How do I put my GE washer in diagnostic mode?

Common GE washer problems might include a broken door lock or an error code you dont understand. Repair Clinic will help you make sense of it all. Need help finding your model number?

Why is my GE Washer not filling up all the way?

Machine Wont Fill If your washer wont fill, check the hot and cold faucets to make sure theyre both turned on fully. … Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.

FAQ

How do you run a diagnostic on a GE washing machine?

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
3. The motor has now been reset and is ready for you to start a cycle.

How do I reset my GE top load washer?

How do you run a diagnostic on a washing machine?

How do I reset my GE washer control board?