Guide

How To Reset Fisher And Paykel Dishwasher

Webster West

how-to-reset-fisher-and-paykel-dishwasherFisher & Paykel may not be as well-known as Whirlpool or Ge, but it produces many of the same appliances, such as dryers, washing machines, and dishwashers. Dishwashers from Fisher Paykel are designed to make dishwashing a breeze!

Depending on the model, Fisher & Paykel dishwashers may have one or two drawers. These are referred to by the company as Dish Drawers. When these dishwashers cause problems, users can diagnose and reset them without the help of professionals.

You must press and hold the key/lock button for 5 seconds to reset a Fisher & Paykel dishwasher. After that, push the power button to turn off the dishwasher. Wait 2-3 minutes before turning on the dishwasher with the power switch. The dishwasher is reset once the electricity is restored.

In this article, we’ll discuss how to reset the Fisher and Paykel dishwasher and its troubleshooting.

Reset Procedures for the Fisher & Paykel Dishwasher
  1. Press and hold the button decorated with the key and lock image for five seconds. …
  2. Press the power button to turn off power to the Fisher & Paykel dishwasher.
  3. Wait a few minutes and then press the power button to restore power.

Here you will find a complete step-by-step guide on how to reset this dishwasher to get rid of annoying problems.

If your Fisher & Paykel DishDrawer is acting abnormally, or showing some unknown error codes or beeping, then it is best practice to reset it.

How Do I Know if There is a Fault?

  • Your dishwasher will beep continuously and a fault code will flash in the display.
  • Note down the fault code.
  • You may be able to fix some faults yourself – see the table on the following page.
  • If you cannot clear the fault, contact Customer Care for support or to organize a visit by a service technician (See ‘Service and warranty’ booklet for contact details).

Double models only:

  • The drawer indicator will also flash to show which drawer has a fault.
  • If there is a fault in both drawers, both drawer indicators will flash.
    • Press Fault Code.JPG to scroll between the drawers.
    • Note down the fault codes for each drawer. There may be two different codes flashing if the faults are different in each drawer.
  • If a fault occurs in one drawer only you are still able to use the other drawer.
  • If you have paused a drawer during a wash program, and the other drawer then faults, the paused drawer indicator will continue flashing but will be dimmed.

If the display is showing an F Codes.JPG fault code, you may be able to clear the fault by resetting the dishwasher – see the steps below. If the fault persists, note down the code before disconnecting the dishwasher from the water and power supplies and contact Customer Care.

  • Press to stop the beeping. Press again to turn the dishwasher off.
  • Wait a few seconds. Press again to turn the dishwasher back on.

    • If the fault code has disappeared then the fault has been reset and you can continue to use your dishwasher.

    If the display is showing an ‘A’ fault code, follow the steps below to try and fix the issue. If the fault persists, note down the code before disconnecting the dishwasher from the water and power supplies and contact Customer Care.

    Display Possible Cause What To Do
    Water supply fault
    1. Ensure the water supply is turned on.
    2. Press Start Button.JPG once to stop the beeping, and then again to clear the fault.
    3. Press Start_Pause Button.JPG to resume the wash program.
    Drawer cannot drain. The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked.
    1. Ensure the drainage hose and connection to pipes are not blocked.
    2. Press Start Button.JPG once to stop the beeping, and then again to clear the fault.
    3. Press Start_Pause Button.JPG to resume the wash program.
    The spray arm has loosened or come off its mounting, or water pressure is too low.
    1. Open the drawer and check the spray arm.
    2. If the spray arm has loosened or come off its mounting, re-fit it. Check that it is firmly seated and turns freely (See “User maintenance instructions”).
    3. Press Start Button.JPGonce to stop the beeping, and then again to clear the fault.
    4. Press Start_Pause Button.JPG to resume the wash program.
    Auto recovery program: Dishwasher has detected excess foam in the drawer.
    1. Let the auto recovery program run until it is complete. The wash program will resume when the auto recovery program has completed.
    2. Check that you are using the right detergent before running another wash program.
    3. If the drawer is still filled with foam at the end of the wash program, contact customer care.

    (DD*C Models Only)

    		 Sanitize cycle hasn’t met temperature needed to sanitize dishes.
    1. Check if the water supply has been turned off or the wash program interrupted.
    2. Press Start Button.JPG once to stop the beeping, and then again to clear the fault.
    3. Run the sanitize cycle again.

    Step By Step Process To Reset Fisher And Paykel Dishwasher

    To reset this dishwasher, users must follow these four steps:

  • Release the button five seconds after pushing and holding it with the key and lock .
  • Press the power button on the Fisher & Paykel dishwasher to turn the electricity off.
  • Press the power button to restart the machine after a brief delay.
  • The dishwasher should be turned off and disconnected from the wall outlet if the issue continues.

    • Observe these steps to clean the drain filter:

  • Remove the DishDrawer’s plug from the power source.
  • On the base rack, raise the drain filter access panel (if fitted).
  • The drain filter should be lifted out.
  • Replace the item into the designated space after emptying, cleaning, and running water.
  • Make sure the filter plate is flush with the drain filter.
  • Reconnect the power supply to the DishDrawer.

    • FAQ

    How do I reset my Fisher and Paykel f1 dishwasher?

    1. Locate the drain-access filter panel on the bottom of the drawer.
    2. Remove the rack that sits above it.
    3. Pull up to lift the drain filter and remove it from the machine.
    4. Set the filter under the faucet to rinse it clean with cold water.
    5. Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.

    Why is my Fisher and Paykel dishwasher beeping?

    The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. once to stop the beeping, and then again to clear the fault. to resume the wash program.

    How do you run a diagnostic on a Fisher Paykel dishwasher?

    Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

    How do I cancel my cycle Fisher and Paykel dishwasher?

    To activate, press and hold until you hear two beeps (5 seconds). The light above the button will glow steadily. To cancel, press and hold until the light above it goes out. Keep this document handy for easy reference.

    Related Posts

    Guide

    100 Gram Of Chicken Protein

    Webster West
    Guide

    Trader Joes Hashbrown Calories

    Webster West