Kitchenaid Ice Maker Reset Button

Well, if you have a similar issue with your Kitchenaid refrigerator, a reset is the only fix for the problem.

Ice Maker Reset

Press the plastic tab on the door jamb. This signals the light to switch off. Close the freezer door and let it reset for 10 seconds prior to opening the door. Tap the door’s switch at least three times and close the door.

KitchenAid Ice Maker Water Supply Issue:

When the KitchenAid ice maker is not filled with sufficient water either it will be unable to produce ice or will make deficient, malformed cubes. Usually, there is an issue in the water supply system when your ice maker does not fill adequately.

Following are the issues that can affect an ice maker’s water supply system.

If your KitchenAid ice maker is not making ice, it might be due to a defective water inlet valve.

The water inlet valve is an electrically managed valve that is responsible for supplying the water to the ice maker and dispenser. Hence if the valve is out of order or has inadequate water pressure, it will restrain the water to flow through it.

For optimal function, the water inlet valve needs at least 20 psi pressure. So, ensure that the water inlet valve is getting a water pressure of at least 20 psi.

However, if the water pressure is adequate check the power of the water inlet valve with the help of a multimeter. In case, if it is defective you need to replace it.

If the water filter is clogged with debris or minerals, it will restrain the water supply to the ice maker thus reducing the ice production. So, if you haven’t replaced your water filter for the last six months; there are chances that your filter might have been blocked.

Therefore, to prevent clogs it is recommended to change the water filter after every 6 months. Moreover, you can change it more frequently if the ice cubes start to taste bad.

Look for the kinks in the water line as they can also limit the water flow thus decreasing the ice production. So if possible, gently unkink the water line. However, you need to replace the water line if it is damaged.

Sometimes the residual water present in the water line can freeze thus causing a blockage and restricting the water supply to the ice maker. Therefore, a hairdryer can be used to melt the blockage and allow the water to flow.

Nonetheless, keeping the freezer temperature within the particular range can lessen the chances of the water line getting frozen. Defective Ice Maker’s Module:

Your KitchenAid ice maker won’t generate or dispense ice in the presence of a defective icemaker module. Also, if the ice maker module contains ejector blades; don’t forget to make sure that the ice cubes are not trapped in the blades.

Furthermore, many test points are present in the module that a professional technician can check to identify the issue.

The water filter removes impurities and can get clogged with hard water deposits. This slows down the production of ice. If the KitchenAid refrigerator ice maker is not filling with water, then it could be a problem with the water filter or lines.

The bin sensor inside of the KitchenAid ice maker can get blocked by ice on occasion. This isnt always clear to detect. Remove any ice that has found its way over the sensor.

A set of screwdrivers should be all you need to reset or replace an ice maker. Have some bowls to hold screws and parts as you remove them for convenience. Gather towels and place them under the ice maker so you can quickly wipe up spills that can cause an accident.

A helpful place to find a list of KitchenAid ice maker troubleshooting is in the manual. The lights may blink if the ice maker is jammed with ice. KitchenAid recommends removing ice that has collected on the ejector arm with a plastic utensil.

The water filter in the KitchenAid refrigerator in a busy household should be changed every four months, according to Consumer Reports. If the ice maker continues to not make ice or the lights continue to blink, then check that the water filter has been changed recently and is properly installed.

Frequently asked questions:

There’s no reset button on a Kitchenaid refrigerator. To reboot it, you must unplug its cord. Then plug it back in after 10 minutes.

But, there’s one for its water filter.

The water filter reset button is usually located inside the unit.

When you open your fridge, you might see this on its middle top portion.

But in some models, this could be on the left side of the fridge door.

Wanna know how to reset a Kitchenaid refrigerator?

FAQ

How do I reset my KitchenAid ice maker?

Shut the freezer door and allow it to reset for 10 seconds before opening the door. Press the door’s switch three times and shut the door. Let it sit for a few seconds to reset the ice maker. This should stop the blinking lights.

Why is my KitchenAid ice maker not working?

A common cause for when a KitchenAid ice maker won’t make ice is that the freezer temperature is too high. When the temperature is too high, ice cube production is deficient. Clean the condenser coils and check to ensure the condenser fan is working properly.

How do I reset the control panel on my KitchenAid refrigerator?

The reset button is usually located at the bottom of the ice maker unit or in some cases at the top or on the bottom of the ice tray. Once located, press the button down for a few seconds until you hear a beep sound. Once you hear the beep sound, let go of the button. Once reset, check if the problem has been solved.

Related Posts