Going through hassles of your shark steam mop not steaming? Trust me, I know how frustrating it could be. When it comes to shark steam mop repair, there are some basic kits needed, more on that later.
I have had this same issue with mine too, I made a lot of research on how to fix a shark steam mop and the result worked like magic; not to worry, I’ll explain the exact procedures I used in fixing mine. With shark steam mop being one of the best steam mops around the world, I wouldn’t want to dispose of it so quickly. Would you?
First of all, the basics. Before you panic, make sure your steam mop tank is filled with clean water. It’s a no-brainer, grab your tool lets give it a quick fix.
How to Work the Steam Mop
First of all, you have to know how to work shark steam mops. Steam mops work by heating water from a reservoir tank inside the mop. It needs to a temperature of nearly 250 degrees F that sends a jet of steam down into a mop pad covering the head absorbs the dirt, and the heat of the steam is capable of killing most of the bacteria and grime on the floor. It is a faster and sanitary means of cleaning.
If you compare with traditional mop and bucker cleaning system, you will see the steam mop makes it extremely convenient to quickly touch up floors, and so easy and fast to use.
How to Fix Shark Steam Mop?
Your steam mop is not steaming, what could be wrong?
Many reasons can cause your steam cleaner to stop steaming. Firstly you have to know the actual problem of your steam mop and most of the common problem can be fixed.
By using for over the year, your mop will not work properly and get a lot of common problem. If you can’t fix the problem here and make a decision to replace your steam mop, we are here to help you to fix the steam mop.
It might be calcium clogged up in your mop nozzle. When normal water is heated inside the steam mop, then it releases calcium.
Put normal water which contains hydrogen, oxygen and other minerals. When you boil it, the water becomes vapor. Besides, the minerals stay as remainder. These minerals discharged with the pressures and blocked up at the jets that steam shoots through.
After using your steam mop, make sure that you clean your mop regularly. It will help prevent mineral substances from blockage nozzle.
That’s why the manufacturers recommend that you should use distilled water in the steam mops. The result of not following this instruction is usually a blocked the nozzle.
If your nozzle blocked, you could fix this problem by decalcifying the nozzle. For this, you will need some tools such as Cotton swabs, Vinegar and Paper Clip or similar objects.
Firstly you have to unplug your mop and let it cools down. Make empty the water tank. If you see the spray tip of your steam mop is blocked then insert a paperclip into your mop’s spray tip and move it back and forth. This process will loosen debris that locked the nozzle.
After that, take some white vinegar onto the mop head. Then wipe it with a duster or cotton cloth. This will make sure to prevent further blockage in the mop head area. Next, you need to turn it on and use it as usual.
There is another more effortless technique with vinegar that can be applied.
Take vinegar and distilled water and make a solution with 50% vinegar with 50% distilled water. Put the solution inside the water tank of your shark steam mop, and let them sit overnight. In the morning, please turn on the steam mop and hold it over your sink. Then you need to set the steam setting at the highest level and get prepared for a loud burst and sediments. After disintegration, hope your mop will work just fine. This method is easier and time-consuming also.
Shark steam mop leaves a white spot on the floor
Your Shark steam mop leaves a white spot on the floor when it is left in one position too long or hard water is used in the water tank. Tap water tends to leave that white stain. Basically it’s condensation trapped in there.
To remove the white spot left by your Shark steam mop, moisten one end of a towel with undiluted white vinegar and wipe away the white spot with the towel. Moisten the opposite end of the towel with water and wipe the vinegar from the floor. The vinegar smell will go away once it is dry.
In the future, do not leave your Shark steam mop on the floor with a damp or wet cleaning pad for too long. If you’re using tap water, switch to distilled water. Make sure the cap is securely on the water tank.
FAQ
Why is there no steam coming out of my shark steam mop?
Over time and use, calcium and mineral deposits may build up in your Shark mop’s nozzle, inhibiting the release of steam. When this happens, Shark recommends cleaning the nozzle to remedy the issue. To get the steam flowing again, grab the nozzle cleaner included with your mop.
How do I unclog my steam mop?
- Unplug your steam mop and let it cool completely. …
- Insert a paperclip into the spray tip opening to remove any possible clog.
- Pour vinegar through the mop head to clear any clogs located there.
- Reassemble your steam mop and fill the reservoir with water before attempting to use it again.
Do I need to descale my shark steam mop?
Calcium and mineral deposits can build up and impact the performance of your steam mop over time. To extend the life of your product we recommend that you use distilled water or Shark®’s Water Filtration Bottle. Visit www.SharkClean.com to order.
Why is my shark fabric steamer not working?
